Novel Laboratory-Scaled Modeling of Hybrid SAGD and In Situ Combustion

Simple item page
dc.contributor.advisorMoore, Robert Gordon
dc.contributor.advisorMehta, Sudarshan A
dc.contributor.authorAminfar, Ehsan
dc.contributor.committeememberAguilera, Roberto
dc.contributor.committeememberPereira Almao, Pedro R
dc.contributor.committeememberNowicki, Edwin Peter
dc.contributor.committeememberJia, Na (Jenna)
dc.date2023-02
dc.date.accessioned2022-10-28T18:48:24Z
dc.date.available2022-10-28T18:48:24Z
dc.date.issued2022-10-27
dc.description.abstractProper modelling of the emerging technologies in the laboratory is imperative. After reviewing an array of models designed and built-in industry and academia, it was found that models built in academia generally compromise the accuracy of the physical model due to financial burdens associated with construction and operation of such models. In addition, due to conflict in scaling parameters of the recovery technologies, namely SAGD and ISC, the conventional packing methods used in such experiments could not satisfy the two technologies’ scaling criteria. To address the previous model’s shortcomings and enable academia to conduct large-scale three-dimensional (3-D) models design and operation, a novel large-scale 3-D physical model was designed to evaluate the prospect of a hybrid air and steam injection technology in a SAGD configuration utilizing up to three well-pairs. For each test, the 3-D model was packed with a low oil saturation core or lean zone, representing the reservoir portion swept by steam and a high oil saturation core or rich zone representing the un-drained zone between two coalesced steam chambers. These zones were made with preserved native “lean” and “rich” cores from Athabasca reservoirs. Steam was injected into the model to develop a representative steam chamber in the lean zone. This novel model is differentiated from other existing models by size and geometry, a unique heater design and operation strategy and a proprietary packing technique that mimics SAGD chambers at time zero. The one million dollar project was a collaboration the University of Calgary’s In Situ Combustions Research Group (ISCRG) and Statoil Canada’s (now Equinor) to define the representative test criteria using more than one metric tonne of frozen native core material as packing in the three experiments. Multiple disciplines in academia were involved to operate the technology. Test #1 ran at 3,000 kPag (435.1 psig), proving the mechanical integrity of the set up. It revealed a need to re-design the heaters for an optimal outcome. The Test #2 at 2,700 kPag (392.0 psig) and the Test #3 was done at 2,650 kPag (384.35 psig) . Each test utilized Statoil Canada’s (now Equinor) native core and oil samples with a focus on injecting water/steam with air and testing the infill well concept. Analysis of the data demonstrated the ISC process spontaneously ignited immediately after introducing air to the steamed reservoir. ISC addresses a deficiency of SAGD by recovering irreducible oil to steam in the chambers and the untouched oil left in the ‘wedges’ trapped between two chambers by roughly 23.8% which is within range of the simulation modelling. Significant upgrading of oil was observed compared to the original bitumen as well as the difference in the properties of the oil produced from the top and bottom production wells. This production was achieved by burning roughly 75% of the core material and mobilizing 80% of the initial water saturation including the water injected during steaming. 15.5 % of the oil in-place was consumed as fuel. The subject 3-D model’s integrity was achieved and a best practice operation was established.en_US
dc.identifier.citationAminfar, E. (2022). Novel laboratory-scaled modeling of hybrid SAGD and In Situ Combustion (Doctoral thesis, University of Calgary, Calgary, Canada). Retrieved from https://prism.ucalgary.ca.en_US
dc.identifier.urihttp://hdl.handle.net/1880/115386
dc.identifier.urihttps://dx.doi.org/10.11575/PRISM/40374
dc.publisher.facultySchulich School of Engineeringen_US
dc.publisher.institutionUniversity of Calgaryen
dc.rightsUniversity of Calgary graduate students retain copyright ownership and moral rights for their thesis. You may use this material in any way that is permitted by the Copyright Act or through licensing that has been assigned to the document. For uses that are not allowable under copyright legislation or licensing, you are required to seek permission.en_US
dc.subjectISCen_US
dc.subjectHybrid SAGDen_US
dc.subjectIn Situ Combustionen_US
dc.subjectLaboratory Modelen_US
dc.subject3-D Modelen_US
dc.subject.classificationEngineeringen_US
dc.subject.classificationEngineering--Petroleumen_US
dc.titleNovel Laboratory-Scaled Modeling of Hybrid SAGD and In Situ Combustionen_US
dc.typedoctoral thesisen_US
thesis.degree.disciplineEngineering – Chemical & Petroleumen_US
thesis.degree.grantorUniversity of Calgaryen_US
thesis.degree.nameDoctor of Philosophy (PhD)en_US
ucalgary.item.requestcopytrueen_US
Files
Original bundle
Now showing 1 - 1 of 1
Thumbnail Image
Name:
ucalgary_2022_aminfar_ehsan_revised.pdf
Size:
353.59 MB
Format:
Adobe Portable Document Format
Description:
ucalgary_2022_aminfar_ehsan.pdf
Download
License bundle
Now showing 1 - 1 of 1
No Thumbnail Available
Name:
license.txt
Size:
2.62 KB
Format:
Item-specific license agreed upon to submission
Description:
Download
Collections
Open Theses and Dissertations